Hardware

These stainless steel butterfly hose clamps are the ideal choice for connecting silicone tubing to quick disconnects, pumps, and more. The butterf...

These stainless stepless clamps tighten in an exact circle, making them ideal for use with draft lines. Suitable for 3/4" OD tubing (17-20 mm OD). ...

Two things: 1)You may need an extra one to make another starter or2)Sometimes we drink while we brew and we accidentaly pitch the magnet bar right...

Full Coupler with 1/2" Female Pipe Thread. Full couplers have threads for insertion from both sides. 304 stainless. Also used to connect fittings. ...

Stainless Steel Faucet Shank Dimensions: 3-3/4" - Total Length (Tip to Tip) 2-1/8" - Shank Length (Without Nut & Nipple) 1-1/4" - Thread Lengt...

Dip tube o-rings compatible with all homebrew ball lock or pin lock kegs. Slide the o-ring onto the dip tube and then place the dip tube back in th...

If you’re a beermaker who focuses on maintaining a sanitary brewing setup, you will like the advantages of using tri-clover connects any place you ...

Adapt 1/4" male pipe thread to 1/4" male flare thread, making any 1/4" FPT fitting compatible with flare fittings or flare threaded Duotight fittin...

Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 5/16 in. tailpiece is commonly use...

Replacement ball valve for Gen 4 BrewZillas. The valve has been updated since the Gen 3.1.1 model as it has a different grooved tail end capable of...

High temperature o-ring for our weldless valve kits that require only one o-ring. O-ring measures 3/4" ID, and 1 1/4" OD.

Do you have a kettle or cooler but would like the ease and convenience of using a ball valve to easily drain liquid? Are you a Do It Yourself Type ...

This stainless steel bulkhead is 1/2" FPT x 1/2" FPT with a flat, thick rubber washer that makes is very easy to install on most kettles. You will...

This stainless steel bulkhead is 1/2" FPT x 1/2" FPT with a flat, thick rubber washer that makes is very easy to install on most kettles. You will...

Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 1/4" or 5/16" ID tubing to 3/8" ID tubing. The 3/8...

Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 5/16" or 3/8" ID tubing....

Replacement o-ring for the ball valve included with the KegLand Bucket Buddy stainless fermenter. Please note the color of the O-ring recently cha...

Replacement o-ring for the racking arm included with the KegLand Bucket Buddy stainless fermenter. Single o-ring. If you are replacing both o-ring...

Type A Camlock Fitting. Male Camlock with 1/2" Female BSP. 304 Stainless steel construction. 150 psi working pressure.

Replacement seals for female camlocks. Compatible with Type B, C and D. Comes in pack of 5.

Type E Camlock Fitting. Male Camlock with 1/2" Barb (13mm). 304 Stainless steel construction. 150 psi working pressure.

Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 1/2" OD barb for tubing on the other side.

Male Garden Hose Thread on one side, 1/2" OD Barb on the other. Useful for setting up your wort chiller and water filter.