Hardware

Two things: 1)You may need an extra one to make another starter or2)Sometimes we drink while we brew and we accidentaly pitch the magnet bar right...

Full Coupler with 1/2" Female Pipe Thread. Full couplers have threads for insertion from both sides. 304 stainless. Also used to connect fittings. ...

Dip tube o-rings compatible with all homebrew ball lock or pin lock kegs. Slide the o-ring onto the dip tube and then place the dip tube back in th...

Adapt 1/4" male pipe thread to 1/4" male flare thread, making any 1/4" FPT fitting compatible with flare fittings or flare threaded Duotight fittin...

Compatible with either your sanke keg coupler or draft shank and held in place with a hex nut & gasket. This 5/16 in. tailpiece is commonly use...

Replacement ball valve for Gen 4 BrewZillas. The valve has been updated since the Gen 3.1.1 model as it has a different grooved tail end capable of...

High temperature o-ring for our weldless valve kits that require only one o-ring. O-ring measures 3/4" ID, and 1 1/4" OD.

Do you have a kettle or cooler but would like the ease and convenience of using a ball valve to easily drain liquid? Are you a Do It Yourself Type ...

This stainless steel bulkhead is 1/2" FPT x 1/2" FPT with a flat, thick rubber washer that makes is very easy to install on most kettles. You will...

This stainless steel bulkhead is 1/2" FPT x 1/2" FPT with a flat, thick rubber washer that makes is very easy to install on most kettles. You will...

Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 1/4" or 5/16" ID tubing to 3/8" ID tubing. The 3/8...

Stainless steel splicer fitting for joining different sizes of tubing. Recommended for splicing 3/16" or 1/4" ID tubing to 5/16" or 3/8" ID tubing....

Replacement o-ring for the ball valve included with the KegLand Bucket Buddy stainless fermenter. Please note the color of the O-ring recently cha...

Replacement o-ring for the racking arm included with the KegLand Bucket Buddy stainless fermenter. Single o-ring. If you are replacing both o-ring...

Type A Camlock Fitting. Male Camlock with 1/2" Female BSP. 304 Stainless steel construction. 150 psi working pressure.

Replacement seals for female camlocks. Compatible with Type B, C and D. Comes in pack of 5.

Type E Camlock Fitting. Male Camlock with 1/2" Barb (13mm). 304 Stainless steel construction. 150 psi working pressure.

Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 1/2" OD barb for tubing on the other side.

Male Garden Hose Thread on one side, 1/2" OD Barb on the other. Useful for setting up your wort chiller and water filter.

Useful piece for connecting tubing to a Wort Chiller. Female Garden Hose on one side, with a 3/8" OD barb for tubing on the other side.

This Duotight reducer fitting can be attached to the Intertap Short Shank with 1/4" Duotight compatible barb. Duotight offers superior quality when...

These stainless stepless clamps tighten in an exact circle, making them ideal for use with draft lines. Suitable for 1/4" OD tubing (6-8 mm OD). Co...

EPDM gasket for 2" tri-clamp connection. Temperature rated from -30°F to 300°F.

This is the installation tool to install spigots in the Vintage Shop ported PET carboys.The wrench has a specially molded hex nut to hold the 5/16 ...